What ports does RabbitMQ use?

Question

PORT 4369: Erlang makes use of a Port Mapper Daemon (epmd) for resolution of node names in a cluster. Nodes must be able to reach each other and the port mapper daemon for clustering to work.

PORT 35197 set by inet_dist_listen_min/max Firewalls must permit traffic in this range to pass between clustered nodes

RabbitMQ Management console:

• PORT 15672 for RabbitMQ version 3.x
• PORT 55672 for RabbitMQ pre 3.x

PORT 5672 RabbitMQ main port.

For a cluster of nodes, they must be open to each other on 35197, 4369 and 5672.

For any servers that want to use the message queue, only 5672 is required.

What ports is RabbitMQ using?

Default: 5672, the manual has the answer. It's defined in the RABBITMQ_NODE_PORT variable.

https://www.rabbitmq.com/configure.html#define-environment-variables

The number might be differently if changed by someone in the rabbitmq configuration file:

vi /etc/rabbitmq/rabbitmq-env.conf

Ask the computer to tell you:

sudo nmap -p 1-65535 localhost

Starting Nmap 5.51 ( http://nmap.org ) at 2014-09-19 13:50 EDT
Nmap scan report for localhost (127.0.0.1)
Host is up (0.00041s latency).
PORT      STATE         SERVICE
443/tcp   open          https
5672/tcp  open          amqp
15672/tcp open  unknown
35102/tcp open  unknown
59440/tcp open  unknown

Oh look, 5672, and 15672

Use netstat:

netstat -lntu
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address               Foreign Address             State
tcp        0      0 0.0.0.0:15672               0.0.0.0:*                   LISTEN
tcp        0      0 0.0.0.0:55672               0.0.0.0:*                   LISTEN
tcp        0      0 :::5672                     :::*                        LISTEN

Oh look 5672.

use lsof:

eric@dev ~$ sudo lsof -i | grep beam
beam.smp  21216    rabbitmq   17u  IPv4 33148214      0t0  TCP *:55672 (LISTEN)
beam.smp  21216    rabbitmq   18u  IPv4 33148219      0t0  TCP *:15672 (LISTEN)

use nmap from a different machine, find out if 5672 is open:

sudo nmap -p 5672 10.0.1.71
Starting Nmap 5.51 ( http://nmap.org ) at 2014-09-19 13:19 EDT
Nmap scan report for 10.0.1.71
Host is up (0.00011s latency).
PORT     STATE SERVICE
5672/tcp open  amqp
MAC Address: 0A:40:0E:8C:75:6C (Unknown)    
Nmap done: 1 IP address (1 host up) scanned in 0.13 seconds

Try to connect to a port manually with telnet, 5671 is CLOSED:

telnet localhost 5671
Trying 127.0.0.1...
telnet: connect to address 127.0.0.1: Connection refused

Try to connect to a port manually with telnet, 5672 is OPEN:

telnet localhost 5672
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.

Check your firewall:

sudo cat /etc/sysconfig/iptables  

It should tell you what ports are made open:

-A INPUT -p tcp -m tcp --dport 5672 -j ACCEPT

Reapply your firewall:

sudo service iptables restart
iptables: Setting chains to policy ACCEPT: filter          [  OK  ]
iptables: Flushing firewall rules:                         [  OK  ]
iptables: Unloading modules:                               [  OK  ]
iptables: Applying firewall rules:                         [  OK  ]

To find out what ports rabbitmq uses:

$ epmd -names

Outputs:

epmd: up and running on port 4369 with data:
name rabbit at port 25672

Run these as root:

lsof -i :4369
lsof -i :25672

More about epmd options.

Port Access

Firewalls and other security tools may prevent RabbitMQ from binding to a port. When that happens, RabbitMQ will fail to start. Make sure the following ports can be opened:

4369: epmd, a peer discovery service used by RabbitMQ nodes and CLI tools

5672, 5671: used by AMQP 0-9-1 and 1.0 clients without and with TLS

25672: used by Erlang distribution for inter-node and CLI tools communication and is allocated from a dynamic range (limited to a single port by default, computed as AMQP port + 20000). See networking guide for details.

15672: HTTP API clients and rabbitmqadmin (only if the management plugin is enabled)

61613, 61614: STOMP clients without and with TLS (only if the STOMP plugin is enabled)

1883, 8883: (MQTT clients without and with TLS, if the MQTT plugin is enabled

15674: STOMP-over-WebSockets clients (only if the Web STOMP plugin is enabled)

15675: MQTT-over-WebSockets clients (only if the Web MQTT plugin is enabled)

Reference doc: https://www.rabbitmq.com/install-windows-manual.html