sys_execve system call from Assembly

Question

asm_execve.s:

.section .data
file_to_run:
.ascii       "/bin/sh"

.section .text
.globl main

main:
    pushl %ebp
    movl %esp, %ebp
    subl $0x8, %esp         # array of two pointers. array[0] = file_to_run  array[1] = 0

    movl file_to_run, %edi
    movl %edi, -0x4(%ebp)   
    movl $0, -0x8(%ebp)

    movl $11, %eax                      # sys_execve
    movl file_to_run, %ebx              # file to execute       
    leal -4(%ebp), %ecx                 # command line parameters
    movl $0, %edx                       # environment block
    int  $0x80              

    leave
    ret

makefile:

NAME = asm_execve
$(NAME) : $(NAME).s
    gcc -o $(NAME) $(NAME).s

Program is executed, but sys_execve is not called:

alex@alex32:~/project$ make
gcc -o asm_execve asm_execve.s
alex@alex32:~/project$ ./asm_execve 
alex@alex32:~/project$ 

Expected output is:

alex@alex32:~/project$ ./asm_execve 
$ exit
alex@alex32:~/project$

This Assembly program is supposed to work like the following C code:

char *data[2];
data[0] = "/bin/sh"; 
data[1] = NULL;
execve(data[0], data, NULL);

Something wrong in system call parameters?

Answer 1

The execve system call is being called, but you are indeed passing it bad parameters.

(You can see this by running your executable using strace.)

There are three problems:

1. .ascii does not 0-terminate the string. (You might get lucky, as there is nothing following it in your .data section in this example, but that's not guaranteed...) Add a 0, or use .asciz (or .string) instead.

2. movl file_to_run, %edi moves the value pointed to by the file_to_run symbol into %edi, i.e. the first 4 bytes of the string (0x6e69622f). The address of the string is just the value of the symbol itself, so you need to use the $ prefix for literal values: movl $file_to_run, %edi. Similarly, you need to say movl $file_to_run, %ebx a few lines further down. (This is a common source of confusion between AT&T syntax and Intel syntax!)

3. The parameters are placed on the stack in the wrong order: -0x8(%ebp) is a lower address than -0x4(%ebp). So the address of the command string should be written to -0x8(%ebp), the 0 should be written to -0x4(%ebp), and the leal instruction should be leal -8(%ebp), %ecx.

---

Fixed code:

.section .data
file_to_run:
.asciz       "/bin/sh"

.section .text
.globl main

main:
    pushl %ebp
    movl %esp, %ebp
    subl $0x8, %esp         # array of two pointers. array[0] = file_to_run  array[1] = 0

    movl $file_to_run, %edi
    movl %edi, -0x8(%ebp)   
    movl $0, -0x4(%ebp)

    movl $11, %eax                      # sys_execve
    movl $file_to_run, %ebx              # file to execute       
    leal -8(%ebp), %ecx                 # command line parameters
    movl $0, %edx                       # environment block
    int  $0x80              

    leave
    ret

Answer 2

You actually don't need to load anything in the other arguments. If you are doing this in x86 the following simpler code will also work:

.global _main
.section .text

.data
file_to_run:
.asciz "/bin/sh"

.section .text
.globl main

_main:
pushl %ebp
movl %esp, %ebp

movl $11, %eax                      # sys_execve
movl $file_to_run, %ebx              # file to execute       
movl $0, %ecx                       # Null value will work too
movl $0, %edx                       # Null will works too
int  $0x80              

leave
ret

This will essentially open a shell terminal after invoking the system call.