How to hide command output in Bash

Question

Use this.

{
  /your/first/command
  /your/second/command
} &> /dev/null

Explanation

To eliminate output from commands, you have two options:

• Close the output descriptor file, which keeps it from accepting any more input. That looks like this:

  your_command "Is anybody listening?" >&-
  

  Usually, output goes either to file descriptor 1 (stdout) or 2 (stderr). If you close a file descriptor, you'll have to do so for every numbered descriptor, as &> (below) is a special BASH syntax incompatible with >&-:

  /your/first/command >&- 2>&-
  

  Be careful to note the order: >&- closes stdout, which is what you want to do; &>- redirects stdout and stderr to a file named - (hyphen), which is not what what you want to do. It'll look the same at first, but the latter creates a stray file in your working directory. It's easy to remember: >&2 redirects stdout to descriptor 2 (stderr), >&3 redirects stdout to descriptor 3, and >&- redirects stdout to a dead end (i.e. it closes stdout).

  Also beware that some commands may not handle a closed file descriptor particularly well ("write error: Bad file descriptor"), which is why the better solution may be to...

• Redirect output to /dev/null, which accepts all output and does nothing with it. It looks like this:

  your_command "Hello?" > /dev/null
  

  For output redirection to a file, you can direct both stdout and stderr to the same place very concisely, but only in bash:

  /your/first/command &> /dev/null
  

Finally, to do the same for a number of commands at once, surround the whole thing in curly braces. Bash treats this as a group of commands, aggregating the output file descriptors so you can redirect all at once. If you're familiar instead with subshells using ( command1; command2; ) syntax, you'll find the braces behave almost exactly the same way, except that unless you involve them in a pipe the braces will not create a subshell and thus will allow you to set variables inside.

{
  /your/first/command
  /your/second/command
} &> /dev/null

See the bash manual on redirections for more details, options, and syntax.

You can redirect stdout to /dev/null.

yum install nano > /dev/null

Or you can redirect both stdout and stderr,

yum install nano &> /dev/null.

But if the program has a quiet option, that's even better.

A process normally has two outputs to screen: stdout (standard out), and stderr (standard error).

Normally informational messages go to sdout, and errors and alerts go to stderr.

You can turn off stdout for a command by doing

MyCommand >/dev/null

and turn off stderr by doing:

MyCommand 2>/dev/null

If you want both off, you can do:

MyCommand 2>&1 >/dev/null

The 2>&1 says send stderr to the same place as stdout.

You can redirect the output to /dev/null. For more info regarding /dev/null read this link.

You can hide the output of a comand in the following ways :

echo -n "Installing nano ......"; yum install nano > /dev/null; echo " done."; 

Redirect the standard output to /dev/null, but not the standard error. This will show the errors occurring during the installation, for example if yum cannot find a package.

echo -n "Installing nano ......"; yum install nano &> /dev/null; echo " done.";

While this code will not show anything in the terminal since both standard error and standard output are redirected and thus nullified to /dev/null.

>/dev/null 2>&1 will mute both stdout and stderr

yum install nano >/dev/null 2>&1

You should not use bash in this case to get rid of the output. Yum does have an option -q which suppresses the output.

You'll most certainly also want to use -y

echo "Installing nano..."
yum -y -q install nano

To see all the options for yum, use man yum.

.SILENT:

Type " .SILENT: " in the beginning of your script without colons.