What is the difference between LALR and LR parsing? [duplicate]

Question

I understand both LR and LALR are bottom-up parsing algorithms, but what's the difference between the two?

What's the difference between LR(0), LALR(1), and LR(1) parsing? How can I tell if a grammar is LR(0), LALR(1), or LR(1)?

Answer 1

At a high level, the difference between LR(0), LALR(1), and LR(1) is the following:

• An LALR(1) parser is an "upgraded" version of an LR(0) parser that keeps track of more precise information to disambiguate the grammar. An LR(1) parser is a significantly more powerful parser that keeps track of even more precise information than an LALR(1) parser.

• LALR(1) parsers are a constant factor larger than LR(0) parsers, and LR(1) parsers are usually exponentially larger than LALR(1) parsers.

• Any grammar that can be parsed with an LR(0) parser can be parsed with an LALR(1) parser and any grammar that can be parsed with an LALR(1) parser can be parsed with an LR(1) parser. There are grammars that are LALR(1) but not LR(0) and LR(1) but not LALR(1).

More formally, an LR(k) parser is a bottom-up parser that works by maintaining a stack of terminals and nonterminals. The parser is controlled by a finite automaton that determines, based on the current state of the parser and the next k tokens of input, whether to shift a new token onto the stack or reduce the top symbols of the stack by applying a production in reverse.

In order to keep track of enough information to make a determination about whether to shift or reduce, LR(k) parsers have each state correspond to a "configurating set," a set of productions annotated with the following information:

• How much of the production has been seen so far, and
• What tokens to expect after the production has been completed (the lookahead)

The first of these pieces of information is used to determine whether the parser may need to do a reduction - if none of the productions in a current state have been completed, there's no reason to do a reduction. The second of these pieces of information is used when doing a reduction to determine whether the reduction should be performed. When deciding whether to reduce, an LR(k) parser looks at the next k tokens of the input stream. If they match the lookahead tokens, the parser will reduce, and otherwise the parser does nothing.

Problems arise in an LR(k) parser when there are conflicts about what the parser should do in a given state. One type of conflict, a shift/reduce conflict, comes up when the parser is in a state where a production has been completed, but the lookahead symbols for that production conflict are also used by another uncompleted production in the state. This means that the parser can't tell whether to perform the reduction or not. A second type of conflict is a reduce/reduce conflict, where the parser knows it has to do a reduction, but two or more reductions are possible and it can't tell which to do.

Intuitively, as k gets larger and larger, the parser has more and more precise information available to it to determine when to shift and when to reduce. If a grammar is not LR(0), for example, the parser might have a state where given no lookahead at all it can't determine whether to shift or to reduce. However, that grammar might still be LR(1) because given an extra token of lookahead, it may be able to recognize that it should definitely shift and not reduce or definitely reduce and not shift.

The problem with LR(k) parsers is that as k gets larger, the number of states can increase exponentially. Lookahead in LR(k) parsers is handled by building more and more states in the parser to correspond to different combinations of productions and lookaheads, so as the number of possible lookaheads increases so does the number of states. Consequently, LR(1) parsers are commonly too large to be practical, and LR(2) or greater is almost unheard of in practice.

LALR(1) was invented as a compromise between the space efficiency of LR(0) parsers and the expressive power of LR(1) parsers. There are several ways to think about what an LALR(1) parser is. Originally, LALR(1) parsers were specified as a transformation that converts LR(1) automata into smaller automata. Although an LR(1) parser may have many more states than an LR(0) automaton, the only difference is that an LR(1) parser may have multiple copies of any particular state in an LR(0) automaton, each annotated with different lookahead information. An LALR(1) parser can be formed by starting with an LR(1) parser, then combining together all states that have the same "core" (the set of productions and their positions), then aggregating all the lookahead information together. This results in a parser that has the same number of states as an LR(0) parser but retains some amount of information about lookaheads to help avoid LR conflicts.

Another view of LALR(1) grammars uses the "LALR-by-SLR" method. LALR(1) parsers can be constructed by starting with an LR(0) parser for a grammar, then creating a new grammar for the language that annotates nonterminals with information about what states in the LR(0) parser they correspond to. The information about the FOLLOW sets of the nonterminals in that grammar can then be used to compute the lookaheads in the LR(0) parser.

The net result is that

• LR(0) parsers are small, but not very expressive.
• LALR(1) parsers are slightly larger due to the lookahead information, but very expressive.
• LR(1) parsers are huge, but extremely expressive.

As for your second question - how do you determine whether a grammar is LR(1) or LALR(1) - the standard approach is to try to build the parsing automata for the LR(1) parser and LALR(1) parser and checking for conflicts. To build the LR(1) parser, you build up the LR(1) configurating sets, then check to see if any of those configurating sets have a shift/reduce conflict or reduce/reduce conflict. To construct an LALR(1) parser, you can either build the LR(1) parser and then condense configurating sets with the same core or can use the LALR-by-SLR method based on the LR(0) parser for the language. More details about how to construct these configurating sets are available in most compilers textbooks. You can also check out the lecture notes from a compilers course I taught in Summer 2012, which cover all of the above parsing methods and a few others.

Hope this helps!