Difference between logical addresses, and physical addresses?

Question

This answer is by no means exhaustive but it may explain it enough to make things click.

In virtual memory systems, there is a disconnect between logical and physical addresses.

An application can be given a virtual address space of (let's say) 4G. This is its usable memory and it's free to use it as it sees fit. It's a nice contiguous block of memory (from the point of view of the application).

However, it is not the only application running, and the OS has to mediate between them all. Underneath that nice contiguous model, there is a lot of mapping going on to convert logical to physical addresses.

With this mapping, the OS and hardware (I'll just call these the lower layers from here on in) is free to put the application pages anywhere it wants (either in physical memory or swapped out to secondary storage).

When the application tries to access memory at logical address 50, the lower levels can translate that to a physical address using translation tables. And, if it tries to access logical memory that's been swapped out to disk, a page fault is raised and the lower levels can bring the relevant data back into memory, at whatever physical address it wants.

In the bad old days when physical addresses were all you had, code had to be relocatable (or fixed up on load) since it could load anywhere. With virtual memory, that code (and data) can be at logical memory location 50 in a dozen different processes at the same time - it's actual physical address will be different however.

It can even be shared so that one physical copy exists in the address space of many processes at once. This is the crux of shared code (so we don't use more physical memory than we need) and shared memory to allow easy inter-process communication).

It is, of course, less efficient than a pure physical-address environment but the CPU manufacturers try to make it as insanely efficient as possible, since it's used heavily. The advantages far outweigh the disadvantages.

logical address is address relative to program. It tells how much memory a particular process will take, not tell what will the exact location of the process and this exact location will we generated by using some mapping, and is known as physical address.

Logical address:- Logical address generated by the CPU . when we are give the problem to the computer then our computer pass the problem to the processor through logical address , which we are not seen this address called logical address .

Physical address :- when our processor create process and solve our problem then we store data in secondary memory through address called physical address

1. An address generated by the CPU is commonly referred to as a logical address. The set of all logical addresses generated by a program is known as logical address space. Whereas, an address seen by the memory unit- that is, the one loaded into the memory-address register of the memory- is commonly referred to as physical address. The set of all physical addresses corresponding to the logical addresses is known as physical address space.
2. The compile-time and load-time address-binding methods generate identical logical and physical addresses. However, in the execution-time address-binding scheme, the logical and physical-address spaces differ.
3. The user program never sees the physical addresses. The program creates a pointer to a logical address, say 346, stores it in memory, manipulate it, compares it to other logical addresses- all as the number 346. Only when a logical address is used as memory address, it is relocated relative to the base/relocation register. The memory-mapping hardware device called the memory- management unit(MMU) converts logical addresses into physical addresses.
4. Logical addresses range from 0 to max. User program that generates logical address thinks that the process runs in locations 0 to max. Logical addresses must be mapped to physical addresses before they are used. Physical addresses range from (R+0) to (R + max) for a base/relocation register value R.
5. Example: Mapping from logical to physical addresses using memory management unit (MMU) and relocation/base register The value in relocation/base register is added to every logical address generated by a user process, at the time it is sent to memory, to generate corresponding physical address. In the above figure, base/ relocation value is 14000, then an attempt by the user to access the location 346 is mapped to 14346.

Logical Vs Physical Address space

An address generated by the CPU is commonly refereed as Logical Address,whereas the address seen by the memory unit,that is one loaded into the memory address register of the memory is commonly refereed as the Physical Address.The compile time and load time address binding generates the identical logical and physical addresses.However, the execution time address binding scheme results in differing logical and physical addresses.

The set of all logical addresses generated by a program is known as Logical Address Space,whereas the set of all physical addresses corresponding to these logical addresses is Physical Address Space.Now, the run time mapping from virtual address to physical address is done by a hardware device known as Memory Management Unit.Here in the case of mapping the base register is known as relocation register.The value in the relocation register is added to the address generated by a user process at the time it is sent to memory.Let's understand this situation with the help of example:If the base register contains the value 1000,then an attempt by the user to address location 0 is dynamically relocated to location 1000,an access to location 346 is mapped to location 1346.

The user program never sees the real physical address space,it always deals with the Logical addresses.As we have two different type of addresses Logical address in the range (0 to max) and Physical addresses in the range(R to R+max) where R is the value of relocation register.The user generates only logical addresses and thinks that the process runs in location to 0 to max.As it is clear from the above text that user program supplies only logical addresses,these logical addresses must be mapped to physical address before they are used.

A logical address is a reference to memory location independent of the current assignment of data to memory. A physical address or absolute address is an actual location in main memory.

It is in chapter 7.2 of Stallings.