Timing/Clocks in the Linux Kernel

Question

I am writing a device driver and want to benchmark a few pieces of code to get a feel for where I could be experiencing some bottlenecks. As a result, I want to time a few segments of code.

In userspace, I'm used to using clock_gettime() with CLOCK_MONOTONIC. Looking at the kernel sources (note that I am running kernel 4.4, but will be upgrading eventually), it appears I have a few choices:

• getnstimeofday()
• getrawmonotonic()
• get_monotonic_coarse()
• getboottime()

For convenience, I have written a function (see below) to get me the current time. I am currently using getrawmonotonic() because I figured this is what I wanted. My function returns the current time as a ktime_t, so then I can use ktime_sub() to get the elapsed time between two times.

static ktime_t get_time_now(void) {
   struct timespec time_now;
   getrawmonotonic(&time_now);
   return timespec_to_ktime(time_now);
}

Given the available high resolution clocking functions (jiffies won't work for me), what is the best function for my given application? More generally, I'm interested in any/all documentation about these functions and the underlying clocks. Primarily, I am curious if the clocks are affected by any timing adjustments and what their epochs are.

Answer 1

Are you comparing measurements you're making in the kernel directly with measurements you've made in userspace? I'm wondering about your choice to use CLOCK_MONOTONIC_RAW as the timebase in the kernel, since you chose to use CLOCK_MONOTONIC in userspace. If you're looking for an analogous and non-coarse function in the kernel which returns CLOCK_MONOTONIC (and not CLOCK_MONOTONIC_RAW) time, look at ktime_get_ts().

It's possible you could also be using raw kernel ticks to be measuring what you're trying to measure (rather than jiffies, which represent multiple kernel ticks), but I do not know how to do that off the top of my head.

In general if you're trying to find documentation about Linux timekeeping, you can take a look at Documentation/timers/timekeeping.txt. Usually when I try to figure out kernel timekeeping I also unfortunately just spend a lot of time reading through the kernel source in time/ (time/timekeeping.c is where most of the functions you're thinking of using right now live... it's not super well-commented, but you can probably wrap your head around it with a little bit of time). And if you're feeling altruistic after learning, remember that updating documentation is a good way to contribute to the kernel :)

To your question at the end about how clocks are affected by timing adjustments and what epochs are used:

CLOCK_REALTIME always starts at Jan 01, 1970 at midnight (colloquially known as the Unix Epoch) if there are no RTC's present or if it hasn't already been set by an application in userspace (or I guess a kernel module if you want to be weird). Usually the userspace application which sets this is the ntp daemon, ntpd or chrony or similar. Its value represents the number of seconds passed since 1970.

CLOCK_MONTONIC represents the number of seconds passed since the device was booted up, and if the device is suspended at a CLOCK_MONOTONIC value of x, when it's resumed, it resumes with CLOCK_MONOTONIC set to x as well. It's not supported on ancient kernels.

CLOCK_BOOTTIME is like CLOCK_MONOTONIC, but has time added to it across suspend/resume -- so if you suspend at a CLOCK_BOOTTIME value of x, for 5 seconds, you'll come back with a CLOCK_BOOTTIME value of x+5. It's not supported on old kernels (its support came about after CLOCK_MONOTONIC).

Fully-fleshed NTP daemons (not SNTP daemons -- that's a more lightweight and less accuracy-creating protocol) set the system clock, or CLOCK_REALTIME, using settimeofday() for large adjustments ("steps" or "jumps") -- these immediately affect the total value of CLOCK_REALTIME, and using adjtime() for smaller adjustments ("slewing" or "skewing") -- these affect the rate at which CLOCK_REALTIME moves forward per CPU clock cycle. I think for some architectures you can actually tune the CPU clock cycle through some means or other, and the kernel implements adjtime() this way if possible, but don't quote me on that. From both the bulk of the kernel's perspective and userspace's perspective, it doesn't actually matter.

CLOCK_MONOTONIC, CLOCK_BOOTTIME, and all other friends slew at the same rate as CLOCK_REALTIME, which is actually fairly convenient in most situations. They're not affected by steps in CLOCK_REALTIME, only by slews.

CLOCK_MONOTONIC_RAW, CLOCK_BOOTTIME_RAW, and friends do NOT slew at the same rate as CLOCK_REALTIME, CLOCK_MONOTONIC, and CLOCK_BOOTIME. I guess this is useful sometimes.

Linux provides some process/thread-specific clocks to userspace (CLOCK_PROCESS_CPUTIME_ID, CLOCK_THREAD_CPUTIME_ID), which I know nothing about. I do not know if they're easily accessible in the kernel.